Snowman TP Cozy

Christmas is my favorite time to create new little loomed lovelies for the holiday; however, I've been hard at work on pattern revisions for publication, so I've not had much time to blog. In the meantime, my good friend Althea Burger sent me her latest creation for the Knifty Knitter Looms, a cute little snowman toilet paper cozy. This little loom knitted cutie was inspired from the crocheted versions from Mary Maxim, but I really like Althea's knitted version much better. The Snowman TP Cozy pattern is listed below or it is available as a PDF file in the Pattern Box on the right. Be sure to post a "thank you" to Althea for sharing this pattern in time for the holiday season!

Althea's Snowman TP Cozy

Size: About 10 inches high
 
Materials

• Looms: 31 peg large gauge knitting loom for the snowman (red Knifty Knitter loom was used) and 8 peg spool loom for scarf
• Yarn: worsted weight in white, burgundy and orange
• Size E crochet hook
• White craft thread & needle
• 3 large buttons for body
• 2 small buttons for eyes
• Yarn needle
• Large white pom pom
• Fiberfill stuffing
• Roll of toilet paper

DIRECTIONS

Body & Head
"E wrap" on the 31 peg loom with white yarn for 38 rows. Pull up loomed edge to hook the loops onto pegs and make a very long "brim". Continue to "E wrap" for the head for 16 more rows. Slightly stuff the head part and tie it off.

Hat
With burgundy yarn,"E wrap" on the 31 peg loom 10 rows, make a brim, then continue to knit 12 more rows. Tie off. Add pom pom.

Scarf
With burgundy yarn, on spool loom, drawstring cast on flat knit for about 25 inches (closing the CO after knitting about six rows). Do a gathered BO. Cut, tie & secure the yarn tails. Stretch it out a little to set the knit stitches.

Nose
Row 1: Using orange yarn and E crochet hook chain 2, sc in second ch from hook. Chain 1, turn.
Row 2:  2 sc in st, ch 1, turn (2)
Row 3: 2 sc in each st, ch 1, turn.(4)
Row 4: 2 sc in first st, sc in next two sts, 2 sc in last st. (6)

Finishing
Cut yarn leaving a tail. Fold piece lengthwise and use yarn needle to sew up the sides to make pointed carrot-like nose. Sew to center of face. Using craft thread and small needle sew large buttons on front of body and small buttons on face for eyes. Tie scarf around neck area. Place hat on head, stretch it a little if necessary.

Ghost angel

When my good friend Althea Burger wanted to make a little loom knitted angel, she decided to modify Boo-Ella, my little Halloween ghost, and I just love what she did. Pictured above is Althea's ghost and angel, which sort of looks like a knitted version of your good & bad conscience. Here's how Althea took the pattern from being "bad to good":

The angel is knit from the head down using the 12 peg KK flower loom and a single strand of 4 ply yarn. To begin, work a drawstring cast on and knit 28 rows; this forms the head and the body.

Close the cast on edge by cinching the beginning drawstring. Bring the yarn tails to the inside and tie off. When I made Boo-Ella, I did a picot bind off. However, Althea didn’t do anything fancy, just threaded a needle thru the loops, took them off the pegs, and tied it off very loosely.(Note: If you wanted to add a little more ruffle to the skirt edge, you could work a basic flat bind off and add one or two extra chain stitches to each peg by knitting off the same peg once or twice during the bind off procedure. )

After removing the angel from the loom, stretch the bottom to shape it into a flared skirt or let the edge curl up just a little; the effect you get here depends on the type bind off you used. If you did the needle thru the loops bind off, then the skirt will curl just a little. If you did extra stitches between the bind off stitches, the skirt will flare out just a bit.

The head is just a 1 "Styrofoam ball stuffed up inside and some yarn threaded thru the neckline on a yarn needle, which is pulled tight and tied off. Embroider eyes and mouth.

The wings are made in two pieces and stitched together. To make one wing, use the 12-peg flower loom and do a drawstring cast on. Knit for 6 rows; finish the cast on and bind off edge the same way you did the angel’s body. After removing from the loom, stretch out the open edge (step 1, pictured below), mash the bell shape flat to form two halves and sew the open edges together matching the stitches (step 2, pictured below). This completes one wing (step 3, pictured below). Make another wing and sew the two wings together where the cinched cast on edges meet. Sew the wings onto the back as one piece along the center-line. The halo is simply a plastic wedding ring used as a party decoration from Wal-Mart. It has a cut in it which allows you to spread it apart, attach it to the stitches of the head, and snap shut so it stays there.

The arms are knit as one piece using two pegs to create a 13 row I-cord. Use the drawstring cast on for it, too. Be sure to leave about a 3 inch yarn tail at both ends. Thread one tail in a yarn needle and push it thru the body below the head on one side and out the other side. Adjust the arms so they are both the same length and tie the tails so it looks like praying hands.

This is optional, but you can tie a jingle bell up inside the angel or make some angels in pastel colors, too.